- #Linux minicom howto how to
- #Linux minicom howto install
- #Linux minicom howto serial
- #Linux minicom howto manual
- #Linux minicom howto windows
This will facilitate connectivity with a multitude of devices, including a simple VT220. For overall interoperability, it is best to set the baud rate of your TNC to 9600, with 8-n-1 for parity. Minicom has a much smaller set of connection speeds. When you are done, A then Z will bring up the help menu and you TNC cmd: prompt and you should now have control of the TNC. Press once or twice if you do not get the Settings and then select Exit to enter minicom.
#Linux minicom howto serial
The serial device and the Bps/par/bits (8/N/1 and whatever the speed Select "Serial port set up" from the list with the cursor keys and set Note that minicom requires root privileges. To start minicom then (assuming you have not configured it, but you In this case, the converter is attached to ttyUSB0, you when youĬonfigure minicom, you want to use /dev/ttyUSB0 as the serial port usb 2-2: pl2303 converter now attached to ttyUSB0 You should get something like this dmesg | grep tty So, plug it in, give it a minute and then type at a console port: It is a serial terminal program that runs from the command line, but can sometimes be a little fussy to get working, and I will admit that I have not used minicom with a USB/Serial converter.įirst, you have to know what tty port your USB/Serial converter is
#Linux minicom howto install
The good news: it is in all the repositories, so you can pull it down and install it quickly. Minicom is an old school program that is available for most of the distributions but may not be installed by default. So, in the interest of helping save you some time, here is a quick write up on using minicom with a USB/Serial adapter to talk to your TNC, specifically, a KPC. It was at this point that I realized I had forgotten more about Linux (and minicom) than I had about the commands needed to control the TNC. It has also served (quite well) as a low-tech 'terminal-window' to allow. It is, in principle, very much like minicom (1), only its 'pico' instead of 'mini' It was designed to serve as a simple, manual, modem configuration, testing, and debugging tool.
#Linux minicom howto how to
Then, from another terminal on a remote PC connected to the same network, use the command described in How to perform ssh connection.Over the weekend, I was showing Linux and Packet radio and for some reason I could not talk to my TNC, a KPC 3+. As its name suggests, picocom is a minimal dumb-terminal emulation program. If the network connection is through Ethernet then "InterfaceNetwork" = "Eth0", else if the network connection is using Wifi then "InterfaceNetwork" = "WLAN0"Įth0 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:FB
#Linux minicom howto manual
More information on the board serial port can generally be found in the hardware user manual of the board.Open a terminal emulator application on your PC and configure with the serial setup menu the USB port to be used and the baud rate of the serial link (in general 115200 baud).
#Linux minicom howto windows
Īny of the Windows terminal emulator applications can be used. On the terminal, the prompt is changed information on Minicom can be found at the following link. See below example for a standard UART (ttyS0) or STLink interface (ttyACM0): how to configure an OS-level serial port on a Linux device so that a Java. See How to use TTY with User Terminal article to find the appropriate tty instance to be used.
Press , and then select the appropriate serial device (for. Select Serial Port Setup and pressHardware flow control is generally set to off (default value is on) and a baud rate of 115200 is usual. At the Linux command prompt, type minicom -s. The UART configuration that is set with the below command has to match the one from your board: to be checked within board user manual. If a message indicating Minicom does not exist, then install it:.You need first to check that Minicom is installed on your PC. Pictures describing board connections can be found in Category:ST boards 1.1 On Linux ® PC 1 Remote terminal via serial link (UART/USB)ġ Remote terminal via serial link (UART/USB)įirst of all, you need to connect your host PC to the board via UART.ĭepending on the board, some additional materials may be needed to physically interconnect the board to the console serial port (extension board or adapter to interconnect the UART from the board to the USB PC input).